How Often Should You Test Your 1-Rep Max?
By Mac Burke, qualified sports nutritionist
The short answer
Test a true 1RM no more than once every 8-16 weeks, at the end of a training block and after a lighter week. Between tests, estimate your max from hard sets of 3-5 reps or from how heavy your working sets feel. Many lifters training for health or muscle never need a true max test.
Testing your max often feels productive, but it is mostly a measurement, not training. Each true test costs a session of recovery and carries more risk than normal sets. For most people, a proper test every two to four months is plenty. The rest of the time, your training sets already show you if you are getting stronger.
Why not test your max every few weeks?
Strength takes time to change, and a 1RM test has some natural noise. A systematic review of 32 studies found 1RM testing is reliable, with a median coefficient of variation of 4.2% between repeat tests (Grgic et al., 2020). On a 100 kg lift, that is roughly a 4 kg swing from session to session that has nothing to do with real progress.
If you test every 2-3 weeks, real gains are often smaller than that noise. You end up chasing numbers and reading meaning into normal day-to-day variation. Testing less often gives your training time to produce a change big enough to see.
There is also a cost. A max day needs a long warm-up and leaves you tired. Time spent testing is time not spent doing the sets that build strength in the first place.
When is the best time to test a 1RM?
Test at the end of a training block, when fatigue is low. A good pattern looks like this:
- Train for a block of 6-12 weeks.
- Take a lighter week with fewer sets and lighter loads to shed fatigue.
- Test the main lifts at the start of the next week, one or two lifts per session.
- Use the new numbers to set loads for the next block.
Expert strength coaches in a 2023 consensus study defined deloading as a period of reduced training stress designed to reduce fatigue and enhance preparedness for the training that follows (Bell et al., 2023). Testing straight after a deload gives a fairer picture of your strength.
Avoid testing after a poor night. A meta-analysis of 69 studies found sleep loss reduced exercise performance by about 7.6% on average, and performance dropped by roughly 0.4% for every extra hour awake before exercise (Craven et al., 2022).
How do you track strength without testing a max?
Use your normal training sets. If you can lift more weight for the same reps, or more reps with the same weight, you are stronger. Three simple methods:
- Estimate from a rep-max. A hard set of 3-5 reps gives a solid estimate using a formula like Epley. One study found 5RM data produced the most accurate predictions of true 1RM, and recommended using no more than 10 reps (Reynolds et al., 2006).
- Track effort at a fixed weight. If your usual 5 reps at 100 kg used to feel like 2 reps left and now feels like 4 left, your max has gone up.
- Watch bar speed if you have a tracker. Bar speed is closely tied to the percentage of 1RM you are lifting, so faster reps at the same weight signal a higher max (Gonzalez-Badillo and Sanchez-Medina, 2010).
Do you need a 1RM at all to train well?
No. Effort-based training works without one. In an 8-week study, trained men either used fixed percentages of a tested 1RM or chose loads to hit a target rating of perceived exertion. Both groups gained strength and muscle with no significant difference between them. The RPE group showed a small, non-significant edge in squat strength (17.1 kg vs 13.9 kg) (Helms et al., 2018).
Effort-based loading also adjusts to good and bad days automatically. If you are tired, the same target effort means a slightly lighter load. That is something a fixed percentage from an old test cannot do.
How do you know when to stop attempts on test day?
Rate each heavy single using reps in reserve. If a single feels like you had 2 reps left, you have room for another jump. If it felt like 0-1 left, that is close to your max. A study that tested this scale during squat 1RM tests found bar speed slowed as ratings rose, and concluded the RIR-based scale can give useful feedback during a 1RM test (Zourdos et al., 2016).
The same study found experienced squatters moved more slowly and rated their true max as harder than novices did. Newer lifters often stop before their real limit, because heavy singles feel unfamiliar. That is another reason beginners get more from estimating than from testing.
For most lifters, a sensible calendar is three or four tests a year at most, each at the end of a block. The rest of the year, let your training sets and estimates do the job.
Who should test their max more often?
Competitive powerlifters and weightlifters need practice with near-maximal loads, especially in the weeks before a meet. Even then, most practise heavy singles at a manageable effort rather than true all-out maxes each week. Beginners sit at the other end. Their strength changes so fast that any max goes out of date in weeks. They are better off adding weight steadily and estimating as they go.
If you lift for health, muscle or general strength, a true max is optional. A rep-max estimate once a block tells you what you need. If you want that tracking done for you, structured programs in the MBM app, launching soon, are built around steady load progression. Early access is at /app.
Common questions
Should I test all my lifts on the same day?
It is better to spread them out. Test the squat and bench on one day and the deadlift on another, or test one lift per session. Fatigue from one heavy lift lowers the next.
What if my max goes down at a test?
Check the obvious first: sleep, stress, food and how hard the previous weeks were. One bad test is common. Look at your training trend over several weeks before deciding your program is not working.
Is a 3RM test safer than a 1RM test?
It uses a lighter load, which many lifters prefer, and still gives a good estimate of 1RM. It is a sensible middle ground if you want hard data without a true max.
How long should I rest between max attempts?
Rest 3-5 minutes between heavy singles. Rushing attempts lowers what you can lift and makes the test less accurate.
Sources
- Grgic et al. (2020), Sports Medicine - Open - Test-retest reliability of the 1RM assessment
- Bell et al. (2023), Sports Medicine - Open - Integrating deloading into strength and physique training: Delphi consensus
- Craven et al. (2022), Sports Medicine - Effects of acute sleep loss on physical performance
- Helms et al. (2018), Frontiers in Physiology - RPE vs percentage 1RM loading in periodized programs
- Reynolds et al. (2006), Journal of Strength and Conditioning Research - Predicting 1RM from multiple-RM testing
- Gonzalez-Badillo and Sanchez-Medina (2010), International Journal of Sports Medicine - Movement velocity as a measure of loading intensity
Ready to apply this to your own program?
MBM builds 1:1 coaching programs around the exact principles above - weekly check-ins, weekly adjustments, and a plan that fits your life.